Advice

How do I reset my LR2 service?

How do I reset my LR2 service?

How do you reset oil service light Land Rover LR2.

  1. Press and hold the trip reset button with the vehicle stationary and in a power mode less than 6 (two positions before starting engine).
  2. While holding the trip reset button, enter the vehicle into power mode 6 (one position before starting engine).

How do you reset the oil life on a 2013 Land Rover LR2?

2013 LAND ROVER LR2 Maintenance Light Reset Instructions

  1. With the engine off, press and hold the trip reset button.
  2. While holding the trip reset button, turn the ignition to run (one position before starting engine).
  3. Release the trip reset button within 10 seconds of turning the ignition to run.

How do you reset the service light on a 2011 Range Rover Sport?

Reset service light indicator Range Rover Sport

  1. Turn off the cars ignition.
  2. Hold down the reset button on the dash board to zero the mileage.
  3. Turn the cars ignition on, but do not start.
  4. A menu will come up, like date/mileage.
  5. Let go and then press the button again.
  6. It will toggle through some options, then get to rst.

How do you reset the oil light on a 2011 Range Rover Sport?

2005-2022 Land Rover Range Rover Sport Oil Service Light Reset Guide

  1. Hold down the TRIP button. With the key off I’m gonna press and hold the TRIP button on the dash.
  2. Turn on your car.
  3. Release and hold the button again.
  4. Display the DIST or DATE.
  5. Hold down the button.
  6. Start your car.

How do you reset a 2008 LR2?

2008 LAND ROVER LR2 Maintenance Light Reset Instructions

  1. With the engine off, press and hold the trip reset button.
  2. While holding the trip reset button, turn the ignition to run (one position before starting engine).
  3. Release the trip reset button within 10 seconds of turning the ignition to run.

How do you reset the service required on a 2012 Range Rover HSE?

How do you reset the service light on a 2010 Range Rover?

2010 Range Rover LR2 Service Interval Reset

  1. With the engine off, press and hold the trip reset button.
  2. While holding the trip reset button, press the START/STOP button to turn the ignition on (do not press the brake pedal).
  3. Release the trip reset button within 10 seconds of turning the ignition to run.

What does it mean when your car says service required?

The service required light is mainly used to remind drivers when it is time to change the oil and filter, but could be used for other fluids or components. In the past, this light was similar to the check engine light and could mean that a fault has been detected by the system.

How do you reset a 2010 Range Rover?

How do you reset the service light on a 2012 Range Rover Sport?

2005-2022 Land Rover Range Rover Sport Oil Service Light Reset…

  1. Hold down the TRIP button. With the key off I’m gonna press and hold the TRIP button on the dash.
  2. Turn on your car.
  3. Release and hold the button again.
  4. Display the DIST or DATE.
  5. Hold down the button.
  6. Start your car.

How do you reset the maintenance light on a 2011 Range Rover Sport?

How do you reset the oil on a Range Rover?

Land Rover Range Rover Oil Service Maintenance Light

  1. Turn the ignition On. Don’t start the engine.
  2. Gear to park position. Open the bonnet (engine hood).
  3. Open the Driver door.
  4. Depress and hold the GAS and BRAKE PEDALS for 60 seconds.
  5. Then turn the ignition to “off” and verify that the light has been reset.

How do you reset the service light on a 2013 Range Rover Sport?

How do you reset the engine management light?

An even simpler way to clear the engine management light is to turn the ignition on and off. This approach achieves the same outcome as the previous step, but without disconnecting the battery. Turn the ignition on and off three times, pausing a second between each cycle. The engine management light should go off.

How do you reset the oil change light on a Land Rover Discovery?

2014-2019 LAND ROVER DISCOVERY SPORT SERVICE LIGHT RESET Open the driver’s door. Hold the accelerator and brake pedals all the way down until you see SERVICE RESETTING in the dash.